Quick Answer: Can You Shock A Pool Without Chlorine?

Which is better liquid chlorine or powder?

Powdered chlorine is the most typical form of chlorine used in a domestic pool environment.

It is typically only slightly more expensive than liquid chlorine but it is much easier to use and has a lower pH, therefore has less impact on your pool’s balance when used..

Can you put too much shock in a pool?

You can, however, use more shock than you need – or less than is sufficient. In other words, while you shouldn’t worry too much about adding a little extra pool shock, there is still a right way and a wrong way to shock your pool if you want to get the best results.

How much chlorine does it take to shock a 10000 gallon pool?

12.5% Liquid Chlorine Pool Shock – Normal Dosage: 1 gallon of shock per 10,000 gallons of water. Shock Dosage: 2 gallons of shock per 10,000 gallons of water. Source: Champion Liquid Pool Shock instructions.

When should I use non chlorine shock?

If you have milky or cloudy hot tub water but your chlorine levels, PH and alkalinity are ok then Non Chlorine Shock will oxidise the products causing this and help restore your water to crystal clear.

Can you use too much non chlorine shock?

Re: Oops too much non chlorine shock….. Should be fine. Leave the lid off and just run the jets for a bit. Shock is only good to a certain amount, any more than that it’s just a waste.

Can you use pool shock instead of chlorine?

Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. … Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock.

What can I use in place of pool shock?

Shock. Common unscented household bleach (sodium hypochlorite) works well to shock a pool.

What is the difference between liquid chlorine and granular chlorine?

Liquid chlorine and granular shock have the same active chemical that sanitizes your pool, what changes is the strength and the way you use it. Liquid chlorine is less costly, unstabilized and comes in liquid form. Granular shock is stabilized and comes in a solid form that dissolves in your pool.

How much chlorine do you need to shock a pool?

The general recommendation is to use 1 pound of cal hypo shock for every 10,000 gallons of pool water, and 10 ounces of sodium hypo with around 12.5% chlorine to sanitize your pool. Make sure the pool water is at its normal level. Make sure your pool’s pH is between 7.2–7.6 and its alkalinity is between 80–120 ppm.

Can you put too much chlorine in a pool?

Having too much chlorine in your pool water can be dangerous. Exposure to high levels of chlorine can cause lung irritation, skin and eye damage, and provoke asthma. … High chlorine levels decrease the pH of your pool’s water, making it more acidic.

How long does a non chlorine shock last?

When using a non-chlorine shock treatment the product does not sanitise, therefore you can generally use your hot tub 20 minutes after adding it to the water.

What is the best granular chlorine?

Sodium Dichlor Granular Chlorine (granular spa shock) It is neither excessively acid nor alkaline in character, and does not quickly deplete at higher water temperatures. If you use dichlor, the quick-dissolving fine granular formulation is the best.

What is the difference between chlorine shock and non chlorine shock?

So what’s the point? When there is a high level of organic waste in the pool, the available chlorine is used up attacking that, giving bacteria free reign to grow. Non-chlorine shock oxidizes the organics and helps clarify pool water. This allows the free chlorine to do its job of attacking bacteria and algae instead.

What does shocking your pool mean?

The term, “Shocking” refers to the process of adding chlorine or non-chlorine chemicals to your pool in order to raise the “free chlorine” level to a point where contaminates such as algae, combined chlorine (also known as chloramines) and bacteria are destroyed.

How often should you put chlorine in pool?

Check the chlorine content of your water at regular intervals, preferably weekly. The ideal value is between 1 and 1.5 mg per litre of water (> 1 ppm and < 1.5 ppm).